McIntosh MA 6200 Stereophonic Preamp Amplifier

Description: Original owner. Professionally cleaned. McIntosh factory description: MA 6200 Features Seven Different Program Sources.The input switch selects from five different sources or you can choose to listen to either of two tape recorders at the push of a button.Precision Step Attenuator Volume.Control Ideal volume control tracking accuracy and noise free performance are two of the considerable benefits of the McIntosh Precision Step Attenuator. It is a thirty-two step, 70 dB range control with unheard of tracking accuracy within 1 dB. The extreme accuracy is obtained through special electronically controlled resistance element trimming. The accuracy and quiet operation are maintained because the switch commutator touches, only the switch contact pad and not the precision resistor elements.True Loudness Compensation.In the past, loudness controls have typically used simple passive circuits connected to a portion of the rotation range of the volume control. As a consequence, loudness compensation accuracy was dependent on many variables such as speaker efficiency, amplifier gain and differences in input level. The MA 6200 loudness control is continuously variable, operates independently of the volume control, and its contour is accurately modeled after the Fletcher Munson family of "Equal Loudness" curves.Five Band Program Equalizer.Five separate controls permit individual musical spectra shaping in two octave segments to satisfy personal preference or program limitations. There is 12 dB plus or minus control at center frequency of the individual segments. The center frequency are 30, 150, 500, 1500 and 10,000 Hz.Dual Tape Monitor And Tape Copy Switches.Two tape recorders can record simultaneously from the program being listened to or you may record from one to the other without interfering with the "Listen" program.Power Guard Indicator and Protection Circuit.Two red power guard indicators indicate when the power amplifier has reached full output. At this point the power guard circuit begins to control amplification dynamically so that you will not hear the harsh distorted sound of square wave clipping. In addition your speakers are protected from burnout.Very Low Impedance Phono Preamplifier.A new state-of-the-art. Technology operational amplifier is arranged in a low impedance circuit to reduce noise to the lowest achievable level. The circuit follows the RIAA equalization curve.Preamp Output - Power Amp Input Connections.Back panel connections provide the ability to insert roomPreamp Output - Power Amp Input Connections.Back panel connections provide the ability to insert room equalizers, reverberation units or other signal processing devices.Low Noise High Performance.Op-Amps New technology low noise operational amplifiers give lower noise and greater band width than conventional devices.Electronic Active Filter Elements."Active filter" technology is used to generate the equivalent of the inductors normally used in equalizer filters. This eliminates the hum pickup of inductance non linearity than often occurs from conventional inductors."LED" Function Indicators.System status is indicated by long life "LED " indicatorsTurn-on Transient Elimination Circuits.Speaker outputs are connected only after power supplies and circuits have stabilized eliminating turn on thumps or clicks.Harmonic Distortion.Harmonic distortion does not exceed 0,05% when measured from the phono input to the speaker output from20 Hz to 20 kHz at all power levels from 250 mW to full rated outnutHarmonic Distortion.Harmonic distortion does not exceed 0,05% when measured from the phono input to the speaker output from20 Hz to 20 kHz at all power levels from 250 mW to full rated output.Auto Turn On/Turn Off.Power to the entire stereo system can be controlled from either the front panel power switch or the turntable's power switch. A current sensing relay connected to the turntable AC power outlets is controlled by the turntable power switch. The relay, in turn controls the AC power to the remainder of the system.Speaker switches for Three Sets of Speakers.Three sets of loudspeaker may be used one at a time, two together, or all three simultaneously. Speaker Protection Circuits Loudspeaker are protected from burnout by the Power Guard circuit and also by other circuit that instantaneously disconnect the speakers in he presence of DC on the output.Specifications Power Output:75watts minimum sine wave continuously average power output per channel, both channel operating into 4 S (20Hz - 20 kHz, THD no more than 0,05%)100 watts minimum sine wave continuously averagepower output per channel, both channel operating into 8 52 (20 Hz - 20 kHz, THD no more than 0,05%)Output Load Impedance:42,82Rated Power Band: 20 Hz to 20 kHzTotal Harmonic Distortion:0,05% (max imum at any power level from 250 milliwatts to rated power per channel20 Hz to 20 kHz)Intermodulation Distortion:0,05% (max imum at any power level from 250 milliwatts to rated power per channel with both chanels operating for any combination of frequencies 20 Hz to 20 kHz)Frequency Response:20 Hz to 20 kHz. +0, -0,5 dB at rated powerHum and Noise:Power Amp: 105 dBA, 100 dB unweighted, below rated outputTape, Aux Input: 100 dBA, 95 dB unweighted below rated outputPhono Input: 85 dBA, 80 dB unweighted, below 10 mV inputDamping Factor:Greater than 30 InputSensitivity / Impedance:Power Amp : 2,5 V/22 k S Tape, Aux: 250 mV/100 k 2Phono: 2 mV/47 k 2, 100 pfAux, Tape : 250 mV with rated inputPhono: 250 mV with rated inputProgram Equalizer: #12 dB at 30, 150, 500, 1500, and 100,000 HzSemiconductors Complement: 42 Transistors; 13 IC; 25Diodes; 1 Silicon Controlled Rectifier ACPower Outlets: 2 Automatic current sensing (green) 3Switched (black)Power Requirement: 120 V, 50/60 Hz; 0,5 to 4 amps (50 to 400 watts)Dimensions: Front Panel (W x H) : 406 x 138 mm (16" x5-7/16) Chassis (W x H x D): 375 x 122 x 330 mm (14-3/4" × 4-13/16" x 13") Including PANLOC shelf and back panel connectors.Knob clearance required is 32 mm (1-1/4") in front of the mounting panelSemiconductors Complement: 42 Transistors; 13 IC; 25Diodes; 1 Silicon Controlled Rectifier ACPower Outlets: 2 Automatic current sensing (green) 3Switched (black)Power Requirement: 120 V, 50/60 Hz; 0,5 to 4 amps (50 to 400 watts)Dimensions: Front Panel (W x H) : 406 x 138 mm (16" x5-7/16") Chassis (W x H x D): 375 x 122 x 330 mm (14-3/4" × 4-13/16" x 13") Including PANLOC shelf and back panel connectors.Knob clearance required is 32 mm (1-1/4") in front of the mounting panelWeight: Net: 13,6 kg (30 pounds) Shipping: 19,1 kg (42 pounds)Finish: Front panel is anodized gold and black with special gold/teal nomenclature illumination.Chassis is blackMounting: Exclusive McIntosh developed professionalPANLOC

Price: 3000 USD

Location: Rose, Oklahoma

End Time: 2024-09-21T11:55:17.000Z

Shipping Cost: N/A USD