1/32 M-1 Weaver Bomb Lift Diorama Accessory Bomber Airfield RESIN2detail 32015

Description: RESIN2detailHigh QualityFree ShippingCustomer Support1/32 M-1 Weaver Bomb Lift Diorama Accessory Bomber Airfield RESIN2detail 32015 1/32 M-1 Weaver Bomb Loading Lift Often seen near bombers, these hydraulic foot-pumped lifts lifted heavy bombs, normally in "cradles", into position within the bomb bay of an aircraft. Delicate and highly accurate. Very hard to make by hand or by traditional resin-casting techniques. Comes in 2 pieces - the main body with all wheels and levers already attached, and the top hydraulic shelf, as pictured. One of the great things about this "kit" is that has such minimal assembly. This allows for a much more detailed and delicate part for your diorama, than would be possible otherwise. Scale = 1/32 Condition = Brand New (unassembled) Shipping = Free via USPS 1st Class A few things to keep in mind about 3D printed accessories such as thisPatience will be required to carefully remove all support structions (pictured) from the part. A light filing or sanding may be needed to fully remove. Utmost attention was given to design so as to minimize the number of these supports, and reduce the burden of removal.3D printer resin tends to be more brittle than traditional cast resin. Go slow and make sure to use a sharp blade. It will crack if too much pressure is appliedFor the thicker bottom supports, I tend to use a razor saw to reduce shear stresses and avoid inadvertently damaging the partWear Optivisors to get in closeWet sand to cut down on dustAttach pieces using CA glue like any other resin part(s)For Ages 17+This product took me approx. 10 minutes to remove from supports Choose from a Huge Selection of Top-Quality Model Kits and Accessory Brands! PaymentShippingReturnsPaymentShippingReturns We accept payment by any of the following methods: PayPal Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner! We offer FREE shipping on Most orders! Your order will be dispatched within 1 working day of receiving payment (Monday-Friday) and you should expect to receive it three to five days after dispatch (for orders sent RM 1st Class). In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement. If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange the product for another one, be it similar or not. You can return a product for up to 30 days from the date you purchased it. Any product you return must be in the same condition you received it and in the original packaging. High QualityFree ShippingCustomer Support1/32 M-1 Weaver Bomb Loading Lift Often seen near bombers, these hydraulic foot-pumped lifts lifted heavy bombs, normally in "cradles", into position within the bomb bay of an aircraft. Delicate and highly accurate. Very hard to make by hand or by traditional resin-casting techniques. Comes in 2 pieces - the main body with all wheels and levers already attached, and the top hydraulic shelf, as pictured. One of the great things about this "kit" is that has such minimal assembly. This allows for a much more detailed and delicate part for your diorama, than would be possible otherwise. Scale = 1/32 Condition = Brand New (unassembled) Shipping = Free via USPS 1st Class A few things to keep in mind about 3D printed accessories such as this ---Patience will be required to carefully remove all support structions (pictured) from the part. A light filing or sanding may be needed to fully remove. Utmost attention was given to design so as to minimize the number of these supports, and reduce the burden of removal. ---3D printer resin tends to be more brittle than traditional cast resin. Go slow and make sure to use a sharp blade. It will crack if too much pressure is applied ---For the thicker bottom supports, I tend to use a razor saw to reduce shear stresses and avoid inadvertently damaging the part ---Wear Optivisors to get in close ---Wet sand to cut down on dust ---Attach pieces using CA glue like any other resin part(s) ---For Ages 17+ ---This product took me approx. 10 minutes to remove from supports RESIN2detail1/32 M-1 Weaver Bomb Lift Diorama Accessory Bomber Airfield RESIN2detail 32015 1/32 M-1 Weaver Bomb Loading Lift Often seen near bombers, these hydraulic foot-pumped lifts lifted heavy bombs, normally in "cradles", into position within the bomb bay of an aircraft. Delicate and highly accurate. Very hard to make by hand or by traditional resin-casting techniques. Comes in 2 pieces - the main body with all wheels and levers already attached, and the top hydraulic shelf, as pictured. One of the great things about this "kit" is that has such minimal assembly. This allows for a much more detailed and delicate part for your diorama, than would be possible otherwise. Scale = 1/32 Condition = Brand New (unassembled) Shipping = Free via USPS 1st Class A few things to keep in mind about 3D printed accessories such as thisPatience will be required to carefully remove all support structions (pictured) from the part. A light filing or sanding may be needed to fully remove. Utmost attention was given to design so as to minimize the number of these supports, and reduce the burden of removal.3D printer resin tends to be more brittle than traditional cast resin. Go slow and make sure to use a sharp blade. It will crack if too much pressure is appliedFor the thicker bottom supports, I tend to use a razor saw to reduce shear stresses and avoid inadvertently damaging the partWear Optivisors to get in closeWet sand to cut down on dustAttach pieces using CA glue like any other resin part(s)For Ages 17+This product took me approx. 10 minutes to remove from supports Choose from a Huge Selection of Top-Quality Model Kits and Accessory Brands! Payment We accept payment by any of the following methods: PayPal Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner! Shipping We offer FREE shipping on Most orders! Your order will be dispatched within 1 working day of receiving payment (Monday-Friday) and you should expect to receive it three to five days after dispatch (for orders sent RM 1st Class). In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement.Returns If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange the product for another one, be it similar or not. You can return a product for up to 30 days from the date you purchased it. Any product you return must be in the same condition you received it and in the original packaging. High QualityFree ShippingCustomer Support 1/32 M-1 Weaver Bomb Loading Lift Often seen near bombers, these hydraulic foot-pumped lifts lifted heavy bombs, normally in "cradles", into position within the bomb bay of an aircraft. Delicate and highly accurate. Very hard to make by hand or by traditional resin-casting techniques. Comes in 2 pieces - the main body with all wheels and levers already attached, and the top hydraulic shelf, as pictured. One of the great things about this "kit" is that has such minimal assembly. This allows for a much more detailed and delicate part for your diorama, than would be possible otherwise. Scale = 1/32 Condition = Brand New (unassembled) Shipping = Free via USPS 1st Class A few things to keep in mind about 3D printed accessories such as thisPatience will be required to carefully remove all support structions (pictured) from the part. A light filing or sanding may be needed to fully remove. Utmost attention was given to design so as to minimize the number of these supports, and reduce the burden of removal.3D printer resin tends to be more brittle than traditional cast resin. Go slow and make sure to use a sharp blade. It will crack if too much pressure is appliedFor the thicker bottom supports, I tend to use a razor saw to reduce shear stresses and avoid inadvertently damaging the partWear Optivisors to get in closeWet sand to cut down on dustAttach pieces using CA glue like any other resin part(s)For Ages 17+This product took me approx. 10 minutes to remove from supports

Price: 27.99 USD

Location: Hackettstown, New Jersey

End Time: 2023-10-28T12:33:21.000Z

Shipping Cost: 0 USD